D-Link Wireless Routers for Home and Small Business > DIR-3040
WAN dropping
Gimpy88:
Hello all,
I purchased this router back in early January, and I must say its been frustrating to say the least. About once a week, the WAN connection will drop, where it shows the modem IS connected but has no available internet connection. This usually doesn't correct itself, and it requires a reboot. Not once has a reboot fixed this issue. Once it is rebooted and no connection is available, I go into the advanced network settings, and change the WAN port speed to 10 Mbps. Once I do this, the router shows it now has an internet connection. Once that's done, I set it back to AUTO, and the connection remains up. Rinse and repeat weekly. That USUALLY works, however, there have been a few times where the only thing that works is leaving it for an hour, and it magically works.
I too suffer from the ConnectToServer failure which fills the syslogs daily.
I have tried several factory resets, its upgraded to the latest available firmware version (1.02 in Canada). As for the modem, it is a TP Link TC7650. I've ruled this out as the issue as I have directly connected a laptop, Raspberry Pi, and an nVidia Shield to the modem with various cat cables, and the modem has an active connection while the DIR-3040 fails to find one.
While writing this post, this came up on my syslog server for the router:
--- Code: ---Apr 15 09:41:08 dlinkrouter syslog: dnssd_clientstub DNSServiceRefDeallocate called with NULL DNSServiceRef
Apr 15 09:41:10 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:10 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:11 dlinkrouter miniupnpd[926]: shutting down MiniUPnPd
Apr 15 09:41:11 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:11 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:11 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 1
Apr 15 09:41:12 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 2
Apr 15 09:41:13 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 3
Apr 15 09:41:13 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:14 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:14 dlinkrouter [RC]: Current Wan interface is eth3 , mode is dhcp
Apr 15 09:41:14 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:14 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect() failed path:/var/run/mdnsd Socket:27 Err:-1 Errno:0 Success
Apr 15 09:41:14 dlinkrouter syslog: dnssd_clientstub DNSServiceRefDeallocate called with NULL DNSServiceRef
Apr 15 09:41:14 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:15 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:15 dlinkrouter [RC]: Wan(eth3) connect Success , Current Wan ip is **MY.IP.ADDRESS**
Apr 15 09:41:15 dlinkrouter syslog: it is advised to use network interface name instead of 10.10.0.1
Apr 15 09:41:15 dlinkrouter miniupnpd[3334]: HTTP listening on port 6352
Apr 15 09:41:15 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:17 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 1
Apr 15 09:41:18 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 2
Apr 15 09:41:19 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:19 dlinkrouter FOTA[3823]: fota_config.c, fota_init_config, 322:
Apr 15 09:41:19 dlinkrouter FOTA[3823]: CA certificate is not set, use default file: /etc_ro/cacert.pem.
Apr 15 09:41:19 dlinkrouter FOTA[3823]: fota_config.c, fota_init_config, 335:
Apr 15 09:41:19 dlinkrouter FOTA[3823]: firmware encryption flag is on.
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: mtk/fota_generate_config.c, main, 1059:
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: Execute config ACTION: config.
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: mtk/fota_generate_config.c, action_config, 778:
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: Now start generating the configuration file.
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: mtk/fota_generate_config.c, main, 1067:
Apr 15 09:41:19 dlinkrouter FOTA_CONFIG[3827]: Done.
Apr 15 09:41:19 dlinkrouter FOTA[3823]: fota.c, main, 1348:
Apr 15 09:41:19 dlinkrouter FOTA[3823]: Execute ACTION: query.
Apr 15 09:41:19 dlinkrouter FOTA[3823]: fota.c, query_latest_firmware_info, 83:
Apr 15 09:41:19 dlinkrouter FOTA[3823]: Now check with the server for the latest firmware information.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota_api_curl.c, get_http_response_code, 167:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: iHttp_code=200.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, query_latest_firmware_info, 116:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: QUERY the latest firmware information success.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, select_firmware_version, 442:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: Now CHOOSE a viable firmware version.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, check_enforced_version, 411:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: Now check enforced version.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, check_enforced_version, 425:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: 'pEnforced_exist' is null pointer.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, select_firmware_version, 488:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: Select upgrade stable firmware.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, select_firmware_version, 502:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: No newer firmware is available.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, main, 1401:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: The value of 'iRet' is not OK.
Apr 15 09:41:20 dlinkrouter FOTA[3823]: fota.c, main, 1439:
Apr 15 09:41:20 dlinkrouter FOTA[3823]: old hnf=false
Apr 15 09:41:20 dlinkrouter syslog: fota_common.c, fota_unlock, 331:
Apr 15 09:41:20 dlinkrouter syslog: fota lock is uninitialized, no need to unlock.
Apr 15 09:41:22 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 1
Apr 15 09:41:22 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:22 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:23 dlinkrouter miniupnpd[3334]: shutting down MiniUPnPd
Apr 15 09:41:23 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 2
Apr 15 09:41:23 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:23 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:24 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 3
Apr 15 09:41:25 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect() failed path:/var/run/mdnsd Socket:27 Err:-1 Errno:0 Success
Apr 15 09:41:25 dlinkrouter syslog: dnssd_clientstub DNSServiceRefDeallocate called with NULL DNSServiceRef
Apr 15 09:41:25 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:26 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:26 dlinkrouter [RC]: Current Wan interface is eth3 , mode is dhcp
Apr 15 09:41:26 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:26 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:27 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:27 dlinkrouter [RC]: Wan(eth3) connect Success , Current Wan ip is **MY.IP.ADDRESS**
Apr 15 09:41:27 dlinkrouter syslog: it is advised to use network interface name instead of 10.10.0.1
Apr 15 09:41:27 dlinkrouter miniupnpd[4556]: HTTP listening on port 6352
Apr 15 09:41:27 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:28 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 1
Apr 15 09:41:29 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 2
Apr 15 09:41:30 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect()-> No of tries: 3
Apr 15 09:41:31 dlinkrouter syslog: dnssd_clientstub ConnectToServer: connect() failed path:/var/run/mdnsd Socket:27 Err:-1 Errno:0 Success
Apr 15 09:41:31 dlinkrouter syslog: dnssd_clientstub DNSServiceRefDeallocate called with NULL DNSServiceRef
Apr 15 09:41:31 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:31 dlinkrouter FOTA[5035]: fota_config.c, fota_init_config, 322:
Apr 15 09:41:31 dlinkrouter FOTA[5035]: CA certificate is not set, use default file: /etc_ro/cacert.pem.
Apr 15 09:41:31 dlinkrouter FOTA[5035]: fota_config.c, fota_init_config, 335:
Apr 15 09:41:31 dlinkrouter FOTA[5035]: firmware encryption flag is on.
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: mtk/fota_generate_config.c, main, 1059:
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: Execute config ACTION: config.
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: mtk/fota_generate_config.c, action_config, 778:
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: Now start generating the configuration file.
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: mtk/fota_generate_config.c, main, 1067:
Apr 15 09:41:31 dlinkrouter FOTA_CONFIG[5039]: Done.
Apr 15 09:41:31 dlinkrouter FOTA[5035]: fota.c, main, 1348:
Apr 15 09:41:31 dlinkrouter FOTA[5035]: Execute ACTION: query.
Apr 15 09:41:31 dlinkrouter FOTA[5035]: fota.c, query_latest_firmware_info, 83:
Apr 15 09:41:31 dlinkrouter FOTA[5035]: Now check with the server for the latest firmware information.
Apr 15 09:41:32 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:32 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:32 dlinkrouter miniupnpd[4556]: shutting down MiniUPnPd
Apr 15 09:41:32 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:32 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:35 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:35 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:35 dlinkrouter [RC]: Current Wan interface is eth3 , mode is dhcp
Apr 15 09:41:36 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:36 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:36 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota_curl.c, send_query_request, 120:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: curl_easy_perform() failed: Couldn't resolve host name.
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota.c, query_latest_firmware_info, 92:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: The value of 'iRet' is not OK.
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota.c, fota_query_action, 786:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: query_latest_firmware_info fail.
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota.c, manual_query_firmware_info, 1119:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: The value of 'iRet' is not OK.
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota.c, main, 1401:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: The value of 'iRet' is not OK.
Apr 15 09:41:36 dlinkrouter FOTA[5035]: fota.c, main, 1439:
Apr 15 09:41:36 dlinkrouter FOTA[5035]: old hnf=false
Apr 15 09:41:36 dlinkrouter syslog: fota_common.c, fota_unlock, 331:
Apr 15 09:41:36 dlinkrouter syslog: fota lock is uninitialized, no need to unlock.
Apr 15 09:41:37 dlinkrouter [RC]: Wan(eth3) connect Success , Current Wan ip is **MY.IP.ADDRESS**
Apr 15 09:41:37 dlinkrouter syslog: it is advised to use network interface name instead of 10.10.0.1
Apr 15 09:41:37 dlinkrouter miniupnpd[5615]: HTTP listening on port 6352
Apr 15 09:41:39 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:39 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:39 dlinkrouter miniupnpd[5615]: shutting down MiniUPnPd
Apr 15 09:41:39 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:39 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:42 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:42 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:42 dlinkrouter [RC]: Current Wan interface is eth3 , mode is dhcp
Apr 15 09:41:43 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:43 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:43 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:43 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:43 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:43 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:43 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:44 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:44 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:46 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:46 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:47 dlinkrouter [RC]: Current Wan interface is eth3 , mode is dhcp
Apr 15 09:41:47 dlinkrouter [RC]: Wan(eth3) Disconnect
Apr 15 09:41:47 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:47 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:48 dlinkrouter [RC]: Wan(eth3) connect Success , Current Wan ip is **MY.IP.ADDRESS**
Apr 15 09:41:48 dlinkrouter syslog: it is advised to use network interface name instead of 10.10.0.1
Apr 15 09:41:48 dlinkrouter miniupnpd[6918]: HTTP listening on port 6352
Apr 15 09:41:48 dlinkrouter [MLD]: mrib_mld_source: failed to detect local source address on 14
Apr 15 09:41:51 dlinkrouter ipsec_setup: ...Openswan IPsec stopped
Apr 15 09:41:51 dlinkrouter FOTA[7401]: fota_config.c, fota_init_config, 322:
Apr 15 09:41:51 dlinkrouter FOTA[7401]: CA certificate is not set, use default file: /etc_ro/cacert.pem.
Apr 15 09:41:51 dlinkrouter FOTA[7401]: fota_config.c, fota_init_config, 335:
Apr 15 09:41:51 dlinkrouter FOTA[7401]: firmware encryption flag is on.
Apr 15 09:41:51 dlinkrouter FOTA_CONFIG[7405]: mtk/fota_generate_config.c, main, 1059:
Apr 15 09:41:51 dlinkrouter FOTA_CONFIG[7405]: Execute config ACTION: config.
Apr 15 09:41:51 dlinkrouter FOTA_CONFIG[7405]: mtk/fota_generate_config.c, action_config, 778:
Apr 15 09:41:51 dlinkrouter FOTA_CONFIG[7405]: Now start generating the configuration file.
Apr 15 09:41:52 dlinkrouter FOTA_CONFIG[7405]: mtk/fota_generate_config.c, main, 1067:
Apr 15 09:41:52 dlinkrouter FOTA_CONFIG[7405]: Done.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, main, 1348:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: Execute ACTION: query.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, query_latest_firmware_info, 83:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: Now check with the server for the latest firmware information.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota_api_curl.c, get_http_response_code, 167:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: iHttp_code=200.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, query_latest_firmware_info, 116:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: QUERY the latest firmware information success.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, select_firmware_version, 442:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: Now CHOOSE a viable firmware version.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, check_enforced_version, 411:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: Now check enforced version.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, check_enforced_version, 425:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: 'pEnforced_exist' is null pointer.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, select_firmware_version, 488:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: Select upgrade stable firmware.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, select_firmware_version, 502:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: No newer firmware is available.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, main, 1401:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: The value of 'iRet' is not OK.
Apr 15 09:41:52 dlinkrouter FOTA[7401]: fota.c, main, 1439:
Apr 15 09:41:52 dlinkrouter FOTA[7401]: old hnf=false
Apr 15 09:41:52 dlinkrouter syslog: fota_common.c, fota_unlock, 331:
Apr 15 09:41:52 dlinkrouter syslog: fota lock is uninitialized, no need to unlock.
--- End code ---
The modem had 0 downtime since it was restarted about 40 minutes earlier.
Any help would be greatly appreciated.
FurryNutz:
Link>Welcome!
What happens if you set the WAN port speed to 100 or 1000 and not Auto?
* Was a Factory Reset performed before and after any firmware updates then set up from scratch? Link> >FW Update Process
Gimpy88:
Yes, factory resets before and after the firmware update. As for the wan port speed, it doesn't really matter what I set it to, I've had it drop both at 1000 and 100.
FurryNutz:
I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. Ask about an RMA.
Link> Tech Support Contact Information
GreenBay42:
Contact D-Link Canada so they can submit a ticket to the engineers. There was an issue with another router that conflicted with an ISP so possibly it is some quirk that the router has with either the modem or ISP.
Navigation
[0] Message Index
[#] Next page
Go to full version