D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-850L => Topic started by: User850L on October 29, 2013, 03:31:28 AM
-
I had an older dlink router that used to work correctly with OpenDNS, and replaced it with this new DIR-850L model. I configured the DNS addresses to point to OpenDNS servers, but the WEB filtering feature is not working anymore.
I contacted their support team and they told me that it looked like my router was not using their DNS servers, although I am sure the addresses are configured correcty.
If anyone has successfully configured the DIR-850L to work with OpenDNS, please tell me the configuration settings you are using.
BTW, I am using FW v1.09.
Thanks a lot!
-
Link>Welcome! (http://forums.dlink.com/index.php?topic=41537.0)
- What region are you located?
- Was a Factory Reset performed before and after any firmware updates then set up from scratch?
Internet Service Provider and Modem Configurations
- What ISP Service do you have? Cable or DSL?
- What ISP Modem Mfr. and model # do you have?
- What ISP Modem service link speeds UP and Down do you have?
- If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT (http://www.practicallynetworked.com/networking/fixing_double_nat.htm) and How NAT Works (http://cognitiveanomalies.com/cisco-nat-how-nat-works/). To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
- Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
- For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.
- Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
- Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
- Turn OFF DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench (http://forums.dlink.com/index.php?topic=53222.0) or try manually inputting the custom DNSs into Setup/Internet/Manual
- Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
- Ensure devices are set to auto obtain an IP address.
- If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
- Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
- Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
- Turn off WISH, and WPS under Advanced.
- WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
- Set current Time Zone, Date and Time. Use an NTP Server (http://forums.dlink.com/index.php?topic=48695.0) feature. Tools/Time.
-
Hi FurryNutz,
From your suggestions list, this is the configuration setting that makes Dlink's DIR-850L work with OpenDNS:
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
I tried them one by one in sequence, but the only setting that really worked was disabling the SPI option under:
Advanced / Firewall Settings / SPI uses = unchecked
Thanks a lot!
Best Regards,
eds01
-
Glad you got it working. Enjoy. ;)