The Graveyard - Products No Longer Supported > DCS-936L
False alarms all day but misses People AND TRUCKS.. and update failed.
cgmendla:
First of all, I tried to reply to a similar thread but there was no reply button on chrome or Firefox.
I purchased a DCS 963l. I'ts under an eave right over the garage door. pointing at the driveway and front door. Temps are in the 60's right now.
I've been playing with this thing for a while and have a couple of issues.
1. When I tried to run the firmware update, it ran forever without finishing..
2. The plugin for the web based setting of the motion detection area doesn't work in either chrome or FF. The plugin downloaded but I don't see the image area tool.
3. I used my android phone to set the image area. I'm ASSUMING that the colored areas are the areas that will be monitored for motion. (you might want to make that clear in the manual. )
4. I've tried settings for sensitivity from 10 through 70 with the same reaults.
* Constant false alerts all day long mostly caused by changes in the sun (the same thing happens with my 933 inside when sunlight coming in changes. I COULD live with that.
* HOWEVER, even at 70 percent sensitivity, it is only detecting motion less than 20 percent of the time.. eg. When one of our cars pulls into the driveway it DOESN"T TRIGGER.. WTH?? it triggers randomly all day but misses an SUV??? If I walk across the field.. ie. constant distance, it only detects me 20 percent of the time.. It missed the mailman and UPS driver today. It seems to have the same issues in daylight and at night. To get to the front door, you pass within 10 feet of the camera.
I have the web based setting to
- 30 seconds between videos and pics
- Didn't change the image contrast etc.
- Trigger by motion (Pics/vids)
-Vide- Pre event 3 seconds - 10 sec max
I am going to try to manually load the firmware from the web interface and also try a reboot from the interface.
I realize that this camera is not designed for outdoor use but I believe I would have the same issues with it inside.
One possible issue is that if there is a false alarm then there is a 30 second period before it starts checking again.. But that doesn't explain missing vehicles let alone people.
OVerall, I'm pretty disappointed with this unit.
cgmendla:
I figured out the motion tool on the web based page. I missed the notice at the top of the browser to allow the plugin.
I also was able to manually run the firmware update. I reset the motion area and sensitivity to 50 percent. I'll update you tomorrow with the results.
FurryNutz:
Link>Welcome!
* Link>What Firmware version is currently loaded? Found on the DCSs web page under status.
* What region are you located?
What Mfr and model is the main host router?
Were you able to set up the camera using the mydlink Lite app?
Are you using a Dynamic IP address ON the camera or a Static IP address ON the camera.
cgmendla:
--- Quote from: FurryNutz on March 01, 2017, 11:18:40 AM ---Link>Welcome!
* Link>What Firmware version is currently loaded? Found on the DCSs web page under status.
* What region are you located?
What Mfr and model is the main host router?
Were you able to set up the camera using the mydlink Lite app?
Are you using a Dynamic IP address ON the camera or a Static IP address ON the camera.
--- End quote ---
I'll get back to you on the firmware. I manually updated it last night. Today I got no less than 25 false alarms, but this illustrious piece of 'technoloty' missed
1. My son getting into his car and pulling out of the driveway (within 10' of the camera)
2. The mailman who also passes within 10'
3. Me coming home in my Ford Explorer.
4. the 6' tall UPS delivery guy
5. All 240 pounds of me right in front of it.
It did trigger when I put my phone RIGHT in front of the lens to measure the wifi signal. It also triggered this morning when I pulled out of the garage (Still dark) and 2 or 3 times when headlights went by on the street.
So, it gives me false alerts all day long for slight shadow changes but it missed a 4000 pound truck and 3000 pound car.. That certainly doesn't inspire confidence. I believe you forward things to Dlink so I'm hoping you can forward my frustration to them.
I am in Pennsylvania, USA
The main router is an actiontec from verizon. My son and I have a number of devices that function with no problems. I am attaching through a belkin router that is in my breezeway and set as a WAP. Devices working include - 2 android phones, 2 wireless printers, a wireless thermostat, a laptop, an ipad,
using wpa/wpa2 personal AES encryption
More Info
Protected Mode > off
802.11e/WMM QoS > on
The signal strength should be good. The belkin is up high and there is a cinder block wall and the wooden beam over the garage door.
Today when I came home, the unit had lost the wifi. I rebooted it (pulled the plug) and it reconnected after about 10 min
Camera NameDCS-936L
Time & Date2017/3/1 17:03:40
Firmware Version1.02.01
Hardware VersionA
Agent Version2.1.0-b11
A couple of points
1 The 933l I have inside on wifi has been working good for about a year and a half. No issues.
2. YEs, I could set up the camera using the app.
3. I checked where the camera is with wifi analyzer on my phone and the signal strength is -70 bd. That could be a problem. I can run ethernet to the garage or under the eve and put a wifi repeater or access point out there.
4. I am set up with 2 wifi points. One in the basement at the far end of the cape cod house and one in my breezeway. All of our other devices work ok with this. They both use the same SSID. I don't see any signal from the basement wap at the camera.
5. I am using gmail for sending the emails. I am probably going to use a different email account. I don't see anything ending up in junk mail.
I see it on my actiontec
PC Name: DCS-936L
Connection Type:
Ethernet
IP Address: 192.168.1.13
Status: Active
Remote Access: Enabled
The router info is
Router Status
Firmware Version: 40.21.24
Model Name: MI424WR-GEN3I
Hardware Version: I
Serial Number: C----
Physical Connection Type: Ethernet
Broadband Connection Type: DHCP
Broadband Connection Status: Connected
Broadband IP Address: 96-----
Subnet Mask: 255.255.255.0
Broadband MAC Address: F8:-----
Default Gateway: 96.2----
DNS Server: 71.242.0.12
71.250.0.12
Broadband IPv6 Address:
Active Status (Router Has Been Active For): 84 hours, 46 minutes
---------------------------------
Questions
1. Is there anything I can do about the sensitivity. I have the setting at 20 percent and most of the screen except where it sees the street is marked with opaque reddish tiles
2. Does anything happen if my 933l is sending an email that would block the 936? IOW, can my dlink account handle 2 emails at once? I would think it could.
3. Am I correct in assuming that the reddish tiles are ACTIVE spots for motion detectors?
One thing I'm probably going to do is put an SD card in and also set it up for FTP. I'm a bit under the weather so it will take a day or so to get that done. I'll try a setting of 30 percent tomorrow and see if that actually sees large vehicles movint.
Sorry about the rambling.
thanks
chris
FurryNutz:
I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. We find that phone contact has better immediate results over using email. I passed this on to D-Link for review as well.
Let us know how it goes please.
Navigation
[0] Message Index
[#] Next page
Go to full version