• December 17, 2017, 09:19:06 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Heater triggers PIR?  (Read 910 times)

novus

  • Level 1 Member
  • *
  • Posts: 2
Heater triggers PIR?
« on: November 28, 2016, 12:26:36 AM »

Hello Guys,

I have a problem with my 2332L camera. The temperatures outside are below 1 °C.
Every time when the heater switched on, the camera detects a PIR event.

2.   2016-11-28 09:18:25 SYSTEM SET HEATER OFF
3.   2016-11-28 09:15:55 SYSTEM SET HEATER HOLD
4.   2016-11-28 09:15:49 SYSTEM SET HEATER HOLD
5.   2016-11-28 09:11:55 SYSTEM SET HEATER OFF
6.   2016-11-28 09:09:28 SYSTEM SET HEATER HOLD
7.   2016-11-28 09:09:22 SYSTEM SET HEATER HOLD

My camera is connect with a Synology Surveillance Station 8 Beta (new with PIR support). Firmware = 1.07.
Do you have an idea, what I can do?

 
 
« Last Edit: November 29, 2016, 07:07:23 AM by novus »
Logged

RYAT3

  • Level 10 Member
  • *****
  • Posts: 2092
Re: Heater driggers PIR?
« Reply #1 on: November 28, 2016, 04:50:54 AM »

It's possible. I have not tested pir motion with a 2330l and its heater.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 43934
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology
Re: Heater driggers PIR?
« Reply #2 on: November 28, 2016, 07:02:00 AM »

What is "driggers"? Did you mean Triggers?

Hello Guys,

I have a problem with my 2332L camera. The temperatures outside are below 1 °C.
Every time when the heater switched on, the camera detects a PIR event.

2.   2016-11-28 09:18:25 SYSTEM SET HEATER OFF
3.   2016-11-28 09:15:55 SYSTEM SET HEATER HOLD
4.   2016-11-28 09:15:49 SYSTEM SET HEATER HOLD
5.   2016-11-28 09:11:55 SYSTEM SET HEATER OFF
6.   2016-11-28 09:09:28 SYSTEM SET HEATER HOLD
7.   2016-11-28 09:09:22 SYSTEM SET HEATER HOLD

My camera is connect with a Synology Surveillance Station 8 Beta (new with PIR support). Firmware = 1.07.
Do you have an idea, what I can do?
Logged
Cable:200mb/10Mb>Motorola MB7420>COVR3902>HP 24pt Gb Switch. 3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,865L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting

novus

  • Level 1 Member
  • *
  • Posts: 2
Re: Heater driggers PIR?
« Reply #3 on: November 29, 2016, 07:07:02 AM »

yes, sorry i mean triggers.. sorry for my bad english.  :-[
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 43934
  • D-Link Global Forum Moderator
    • New DIR-890L Router with SmartConnect™ Technology
Re: Heater triggers PIR?
« Reply #4 on: November 29, 2016, 07:27:02 AM »

  • What Hardware version is your DCS? Look at the sticker behind or under the camera.
  • Link>What Firmware version is currently loaded? Found on the DCSs web page under status.
  • What region are you located?
Logged
Cable:200mb/10Mb>Motorola MB7420>COVR3902>HP 24pt Gb Switch. 3xDGL-4500s,DIR-857,835,827,815,890L,880L,868L,865L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L and 960L.
Go Here>Router Troubleshooting