• March 28, 2024, 03:12:51 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: [1] 2

Author Topic: Full wireless is first activated when I press the "survey" button  (Read 9829 times)

Artoo

  • Level 2 Member
  • **
  • Posts: 41

Hello all

I have a very strange problem with the wireless performance of the 935L.

When the camera is started up (fx after power-loss) the wireless performance is very poor: My DIR-605L (accespoint) says signal level 10% and rate 1-5mbps and I have many drop-outs in the video-stream. When I do a “wireless survey” in the web interface of the 935L the wireless performance is improved a lot: 46% and 39rate. It seems like the full wireless performance of the 935L is first activated when a wireless survey is started, very strange.
This must be bug in the firmware?

Documentation:

Before I press "Survey"

After I press "Survey"

Bitrate before and after


What to do?

Thanks.

Kind Regards
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #1 on: June 19, 2015, 01:22:03 PM »

What is the distance between the camera and router?

What wireless modes are you using?
Test with the following settings ON the router then post the connection rate results here please:
WPA/TPIK only(not WPA2), Auto Channel width, manual channel 11.

  • Any other WiFi routers in the area that maybe causing interferences? Link> Use InSSIDer to find out. How many? Use v3, its free.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #2 on: June 19, 2015, 01:32:40 PM »

What is the distance between the camera and router?

What wireless modes are you using?
Test with the following settings ON the router then post the connection rate results here please:
WPA/TPIK only(not WPA2), Auto Channel width, manual channel 11.

  • Any other WiFi routers in the area that maybe causing interferences? Link> Use InSSIDer to find out. How many? Use v3, its free.

Distance is 2 meters, no walls. Lots of WiFi routers in this area but I don't think this is the cause since everything is working very fine when I do a survey.

WPA/TPIK only(not WPA2), Auto Channel width, manual channel 11: already on.

Don't you think that it is a little bit strange that full wireless performance is first "activated" when I press the "survey" button?

Thanks for your help.

Regards
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #3 on: June 19, 2015, 01:48:50 PM »

Can you post a pic of the InSSIDer results please?
 Adding Screenshots In A Post
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #4 on: June 19, 2015, 02:01:57 PM »

Can you post a pic of the InSSIDer results please?
 Adding Screenshots In A Post

There is two many acces-points to be displayed at the same time in InSSIDer (I have to scroll). More than 20 acces-points right now.

Regards
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #5 on: June 19, 2015, 02:06:09 PM »

You may be in a WiFi congested area. Especially on 2.4Ghz? This will have an impact on how your router and camera operate.

 Managing Signal Congestion
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #6 on: June 19, 2015, 02:11:43 PM »

You may be in a WiFi congested area. Especially on 2.4Ghz? This will have an impact on how your router and camera operate.

 Managing Signal Congestion

I have to disagree with this:
Wireless performance is very very good now - I just have to press the "survey" button" first. If the problem was because to many acces-point in the area then problem would also be present after I press the survey button and it is not.

For me it seems like a special wireless-performance is activated when I press the "survey" button.

Also: as now can see in the images, my two other MyDlink products are performing very fine and stable.

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #7 on: June 19, 2015, 02:14:37 PM »

What FW version is loaded on the router?
Just because it works for a while after doesn't mean it will be later on...still could be a problem.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #8 on: June 19, 2015, 02:20:02 PM »

What FW version is loaded on the router?
Just because it works for a while after doesn't mean it will be later on...still could be a problem.

It has been stable for hours after and I have tested many times and I see the improved performance right after I press the button.

DIR-605L Firmware Version : 2.06

I see exactly the same when the camera is connected to my Cisco-accespoint.

Regards

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #9 on: June 19, 2015, 02:25:59 PM »

Then there maybe an issue with the cameras FW.

You could try upgrading the 605Ls FW:
http://forums.dlink.com/index.php?topic=62642.msg254075#msg254075
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #10 on: June 19, 2015, 02:31:28 PM »

Then there maybe an issue with the cameras FW.

Agree with that. I will contact DLink :)

You could try upgrading the 605Ls FW:
http://forums.dlink.com/index.php?topic=62642.msg254075#msg254075

No firmware there for Hardware B2?

Regards
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #11 on: June 22, 2015, 06:52:02 AM »

There is FW there for Rev B2...
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #12 on: June 22, 2015, 11:11:03 AM »

There is FW there for Rev B2...

Which one?

DIR-605L Rev A Patch v1.16B01 is for Hardware: A1
DIR-605L Rev B Patch v2.08B02 is for Hardware: B1
DIR-605L Rev C Patch v3.04B01 is for Hardware: C1

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Full wireless is first activated when I press the "survey" button
« Reply #13 on: June 22, 2015, 11:11:43 AM »

DIR-605L Rev B Patch v2.08B02 is for Hardware: B1
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Artoo

  • Level 2 Member
  • **
  • Posts: 41
Re: Full wireless is first activated when I press the "survey" button
« Reply #14 on: June 22, 2015, 11:12:53 AM »

DIR-605L Rev B Patch v2.08B02 is for Hardware: B1

But mine is "Hardware Version : B2"   
Logged
Pages: [1] 2