• March 28, 2024, 11:50:52 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: Firewall Settings IPv4 Rules disappear after save  (Read 11235 times)

Jason303

  • Level 2 Member
  • **
  • Posts: 30
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #15 on: November 20, 2015, 07:52:34 AM »

Would you mind loading v1.09 FW and testing the same process please?

Upgraded the firmware to the new beta version: DIR-890L HW:A1 FW:1.09.

After the firmware upgrade I did a factory default reset to the router. I completed the setup initialization of the router. Clicked on Firewall -> IPv4 Rules. The Remaining rules on the bottom of the screen changed from 15 to 24.

1) I create the rule listed above and it changes from Remaining 24 to 23 and lists the rule I created in the table.
2) I click the Save button and the rule I created is deleted and Remaining goes from 23 back to 24.

The upgraded beta firmware doesn't appear to correct the issue.
Logged

Jason303

  • Level 2 Member
  • **
  • Posts: 30
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #16 on: November 20, 2015, 07:53:26 AM »

OK. I've confirmed this on a Windows 7 PC. I'll forward this on to D-Link for review. Please be patient.

Thank you.

Ok thank you!
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #17 on: November 20, 2015, 07:55:04 AM »

 ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Jason303

  • Level 2 Member
  • **
  • Posts: 30
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #18 on: December 01, 2015, 08:32:15 AM »

OK. I've confirmed this on a Windows 7 PC. I'll forward this on to D-Link for review. Please be patient.

Thank you.

So typically how long does one have to wait to hear a response from D-Link on router issues?
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #19 on: December 01, 2015, 09:25:35 AM »

If you emailed them, not sure. I really recommend using Phone contact to get more immediate help and information.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

ongxa41

  • Level 1 Member
  • *
  • Posts: 2
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #20 on: July 13, 2016, 10:46:05 PM »

I am running into the same issue.  I have contacted D-Link for support and I'm awaiting any solution they may have.
This is important for me because I use the rules to turn off internet access using the firewall & not the parental controls.  PC works...but if your kids figure out how easy it is to spoof a MAC address & pick up a free IP address from DHCP, then PC is worthless.  I set up a range of 7 addresses for my wife's and my gear...static the IPs, then set those on one rule to Always Allow.  All other IPs on my network are turned off via rule at the designated time.

Hope they get this fixed.  1.09 firmware made it so this doesn't work anymore.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Firewall Settings IPv4 Rules disappear after save
« Reply #21 on: July 14, 2016, 06:53:30 AM »

Link>Welcome!

  • What region are you located?
  • Has a Factory Reset been performed?
  • Was a Factory Reset performed before and after any firmware updates then set up from scratch?
  Link> >FW Update Process
  • Was the router working before any firmware updates?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.
Pages: 1 [2]