• July 14, 2024, 10:43:03 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Virtual server works only with DMZ  (Read 9965 times)

abecido

  • Level 1 Member
  • *
  • Posts: 4
Virtual server works only with DMZ
« on: July 31, 2013, 10:28:40 AM »

Hi,

My hardware : DIR-825 rev B1, firmware 2.05EU

Virtual server works only if I put server local LAN IP address into DMZ.

I have applied FurryNutz recommendation :

Quote from: FurryNutz
Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

    Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel.
    Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
    Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
    Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench
    Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
    Ensure devices are set to auto obtain an IP address.
    If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
    Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
    Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
    Turn off WISH, and WPS under Advanced.
    WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
    Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.


I have checked DIR-825 IP WAN address, it is a public IP.
Modem's router is disabled.

But Virtual server doesn't work without server IP LAN into DMZ...(with DMZ it works fine, ftp, openvpn, http, etc...)

Any Idea ?


B.R,
Eric.

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Virtual server works only with DMZ
« Reply #1 on: July 31, 2013, 10:34:04 AM »

How is the VS set up? Are you using any other settings on the router besides VS?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

abecido

  • Level 1 Member
  • *
  • Posts: 4
Re: Virtual server works only with DMZ
« Reply #2 on: July 31, 2013, 11:01:40 AM »

Thank's for this quick response.

VS setting :

name      public port   private port   protocol schedule  Inbound filter  IP Adresse
ftpudp     20              20                 UDP      Always    Allow All          192.168.101.105
ftptcp      21              21                 TCP       Always    Allow All          192.168.101.105
openvpn  1194          1194              UDP      Always    Allow ALL         192.168.101.105


No port forwarding
Firewall  TCP/UDP Endpoint independant
No QoS
No Network filter
No Application rules
No Inbound Filter
No Website filter
No ACL
UPnp enabled
Multicast stream enabled
Wan ping response enabled , allow all
DHCP server on
Internet connection : Dynamic IP (ISP provide always the same public routable IP)

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Virtual server works only with DMZ
« Reply #3 on: July 31, 2013, 11:32:15 AM »

What application SW or operation are you attempting to do with VS?
What ISP service do you have? Cable or DSL?
I presume you are attempting to remote access the IP address using the VS feature?
What happens if you disable uPnP?

« Last Edit: July 31, 2013, 11:37:30 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

abecido

  • Level 1 Member
  • *
  • Posts: 4
Re: Virtual server works only with DMZ
« Reply #4 on: July 31, 2013, 12:13:53 PM »


I use ftp and openvpn.

From : Linux Ubuntu server located on internet with public routable ip address
To     : Linux busybox NAS server located at Home
My internet connection is DSL

And that is not working with uPnP disabled.
Logged

abecido

  • Level 1 Member
  • *
  • Posts: 4
Re: Virtual server works only with DMZ
« Reply #5 on: August 01, 2013, 04:19:20 AM »



Oh my god ! I'm too stupid !

The boxes to activate rules in VS was not checked  ::) :o  ;D

Sorry Furry.

I have found something to add to your checklist : "Don't forget to check the boxes !!!!"  ;D



BR
Eric
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Virtual server works only with DMZ (RESOLVED)
« Reply #6 on: August 01, 2013, 07:46:12 AM »

Keeps getting me too sometimes. Glad you found it and it's working. Enjoy.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

polomani

  • Level 1 Member
  • *
  • Posts: 1
Re: Virtual server works only with DMZ
« Reply #7 on: August 30, 2019, 12:40:32 PM »


Oh my god ! I'm too stupid !

The boxes to activate rules in VS was not checked  ::) :o  ;D


@abecido, thanks man, I've been trying to figure out what's going on a few hours in a row.
I didn't notice the checkbox either  :D
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Virtual server works only with DMZ
« Reply #8 on: August 30, 2019, 12:50:55 PM »

 ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.