• April 19, 2024, 11:57:21 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: access control  (Read 4206 times)

dragom

  • Level 1 Member
  • *
  • Posts: 3
access control
« on: May 02, 2012, 03:38:32 AM »

I can't get the scheduler to work every time I set up a schedule to control access to the internet. When I save settings and exit out then go to turn access control on it turns off access right then instead of the scheduled time. What am I doing wrong??? firmware is 1.35.

« Last Edit: May 02, 2012, 03:40:09 AM by dragom »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: access control
« Reply #1 on: May 02, 2012, 06:54:38 AM »

To set up scheduling:
1. Reserve device IP addresses ON the router under Setup/Networking.
2. Set up a schedule under Tools/Schedule on the routers web page. Customize your dates and times here.
3. Use Access Control under Advanced to apply the customized schedule to a policy and to the PC(s) desired to be controlled. 
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

Sammydad1

  • Level 5 Member
  • *****
  • Posts: 722
Re: access control
« Reply #2 on: May 02, 2012, 09:50:08 PM »

you have to save your schedule with a name....

reboot the router....

DNS Relay has to be turned on....

Reboot the router....

When setting up an Access Control policy, the name of the previously created schedule should be in the drop down list.....

Save new policy

Reboot the router....

Logged
DIR-655 A2, FW: 1.35NA

dragom

  • Level 1 Member
  • *
  • Posts: 3
Re: access control
« Reply #3 on: May 03, 2012, 02:50:40 AM »

I still can not get it to work I enter a schedule save it's settings. Then go to access control enable access control a second or 2 after I enable access control it cuts off access to whatever computer I am trying to control no matter what time I have set up in the schedule. I have checked the time on the router and it is right just can't seem to get it to stop turning off access when i don't want it off.
« Last Edit: May 03, 2012, 05:43:55 AM by dragom »
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: access control
« Reply #4 on: May 03, 2012, 07:19:15 AM »

Try swapping time frames?
Maybe someone can review your router settings with you using teamviewer if your interested. Its safe and secure.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

dragom

  • Level 1 Member
  • *
  • Posts: 3
Re: access control
« Reply #5 on: May 03, 2012, 02:59:35 PM »

Try swapping time frames?
Maybe someone can review your router settings with you using teamviewer if your interested. Its safe and secure.

Yeah I tried swapping the times and still turns the computer off. Right now I am willing to try anything. I am not all that up on the router stuff so who knows maybe there is something that I am missing.
Logged

davevt31

  • Level 9 Member
  • ****
  • Posts: 1590
Re: access control
« Reply #6 on: May 03, 2012, 09:10:47 PM »

Also these routers sometimes have issues with a schedule that wraps around Midnight.  If you have one that does it best to make two policies, one that ends at midnight and another that starts at Midnight.
Logged